SIMPLE MECHANISM

  • Home in Hindi
  • Privacy Policy
  • About us
  • Contact us
  • Home
  • WORKSHOP
    • Foundry Shop
    • Smithy Shop
    • Welding Shop
    • Machine Shop
    • Fitting Shop
    • Sheetmetal Shop
  • Blog
  • Blog in Hindi
  • Sand Testing
  • Engineering Videos
  • Others
  • Site Map

Sand Moulding II Green Sand II Dry Sand II Loam Sand Preparation

 All posts, Foundry Shop     No comments   



Green Sand

The mold is prepared by green sand and pouring is done in a sand mold with sand in its green or natural state is known as Green Sand Molding. For producing green sand the mixture is prepared, consisting of silica sand. The following ratio of the green sand.
1.    Clay 10 to 15 %
2.    Moisture 4 to 6 %
The clay and moisture content mixed and riddled it. If required to give proper tempering. After completion, the mixture of sand places the wooden board on the floor for spotting the flask drag part. Place the drag on the wooden board. The wooden board is not compulsory it is optional. After this, the pattern kept between the drag and cope if the pattern is singled. If The pattern is split first place the drag part of the pattern and parted off with the help of strike off bar. The sand is rammed properly and the box turned over. The second part of the pattern is placed in the position followed by cope. Runner and Riser are placed in position and filled the box with sand and rammed properly. At the runner taken out the pouring basin for smooth pouring the material in it. Vent wire is used to provide the vents. The boxes are assembled after removal of the pattern. The mold is prepared.  

Dry Sand


This process is almost similar to the Greensand mold to expect the composition of sand. The composition is different from green sand. For preparing dry sand the special types of the binder are used such as resin, clay or molasses. This is used for producing a strong bond. Here again, the same process is repeated. After completion, the mixture of dry sand, place the drag and insert the pattern. As similarly when required the wooden board if the floor is not smooth then use the boar if not, that is not compulsory it is optional. After this, the pattern kept between the drag and cope. If the pattern is split first place the drag part of the pattern and excess sand is removed the help of strike off bar. The sand is rammed properly and the box turned over. The second part of the pattern is placed in the position followed by cope. Runner and Riser are placed in position and filled the box with sand and rammed properly. Here the same molding box is tempered with oven or stove. Remove the all moisture in the sand with the help of heat. The dry sand mold is prepared.




Loam Sand

The loam sand process is totally different from those two described above. First, the structure of the article is prepared by hand using brick and loam sand. By loam sand and bricks to make the desired shape by means of stickle and sweeps. This is a patternless process. The same procedure is done in the absence of pattern. After completion of the mold, it is baked to give strength. In this, the past of loam sand and clay is prepared for making the mold.
 

Facing Sand





It is called fat sand. The facing sand means this type of sand placed around the pattern. It is freshly prepared and well-tempered sand. Initial coating around the pattern surface given by facing sand.

Parting sand

The parting sand which is name indicated, this is used between two parts and around the pattern for safe removal. The two parts mean cope and drag. The parting sand placed upper surface of drag. The burnt sand and dry silica sand can be used as parting sand.

Floor, Black, and backing sand

These are an interchangeable term and all denoted the used sand which is left on the floor after the casting has done. The left sand can use by refining it. Before reusing it the sand is riddled properly to remove the foreign material like nails and fins. Such sand is called unit sand.

Core sand

The core sand has high silica sand content and used for making core is called core sand.

Oil Sand

The silica sand using oil binder is known as oil sand.

Molasses sand

In this type of sand, molasses is used as a binder. It is very useful for making a mold for small casting. It is also used for making a core.




  • Share This:  
  •  Facebook
  •  Twitter
  •  Google+
  •  Stumble
  •  Digg
Newer Post Older Post Home

0 Comments:

Post a comment

Recent Posts

Youtube

Random

Categories

All posts Engineering Videos Fitting shop Sandtesting Foundry Shop Machine shop Blog in hindi Welding Hindi Smithy shop Sheet Metal Question and Answer other

Popular Posts

  • WHAT IS FITTING SHOP ?
  • WHAT IS FITTING SHOP IN HINDI.
  • Fitting Shop Tools
  • Lathe machine
  • Introduction about Foundry फाउंड्री शॉप के बारे मैं इंट्रोडक्शन

Facebook Page

Blog archive

  • ►  2020 (2)
    • ►  February (1)
    • ►  January (1)
  • ►  2019 (20)
    • ►  December (1)
    • ►  November (3)
    • ►  October (3)
    • ►  September (1)
    • ►  April (5)
    • ►  March (7)
  • ▼  2018 (13)
    • ▼  December (3)
      • Pattern types in casting
      • Sand Moulding II Green Sand II Dry Sand II Loam Sa...
      • Foundry Meaning
    • ►  November (1)
    • ►  October (8)
    • ►  September (1)
  • ►  2017 (17)
    • ►  November (3)
    • ►  October (5)
    • ►  September (2)
    • ►  August (6)
    • ►  July (1)

Follow by Email

Total Pageviews

Pages

  • Privacy Policy
  • About us
  • Contact us
  • Sitemap

Engineers are persons who discover
the world by their pen and their brain

Copyright © SIMPLE MECHANISM | Powered by Blogger
Design by Er Indraj Kumar | NewBloggerThemes.com